DareNET IRCd Configuration

General

Old M:line

The General {} block defines some information about the server itself.

General 
{
  name = "servername";
  vhost = "ipv4vhost";
  description = "description";
  numeric = numericnumber;
};

<virtual host> must contain either a * or a valid IPv4 address in dotted quad notation (e.g. 127.0.0.1). The address MUST be the address of a physical interface on the host. This address is used for outgoing connections only; see Port {} blocks for listener virtual hosting. If in doubt what to put here, use the IP of your primary interface here.

Note that <server numeric> must be unique on the network the server is running, and may be between 0 and 4095. It is not updated on a rehash. If linking to DareNET, you should use the numeric assigned to you by the Server Management team.

Example block:

<source lang="perl">General {

 name = "servername.area.zone.darenet.org";
 description = "DareNET Client Server";
 vhost = "127.0.0.1";
 numeric = 10;

};</source>

Admin

Old A:line

The Admin {} block defines information that can be retrieved with the /ADMIN command.

Admin 
{
  Location = "string 1 here";
  Location = "string 2 here";
  Contact = "string 3 here";
};

Example block:

<source lang="perl">Admin {

 Location = "DareNET";
 Location = "Server Management Team";
 Contact = "<routing@darenet.org>";

};</source>

Classes

Old Y:lines

All connections to the server are associated with a "connection class", whether they be incoming or outgoing (initiated by the server), be they clients or servers.

Class
{
  name = "<class>";
  pingfreq = time;
  connectfreq = time;
  maxlinks = number;
  sendq = size;
  usermode = "+modes";
};

For connection classes used on server links, maxlinks should be set to either 0 (for hubs) or 1 (for leafs). Client connection classes may use maxlinks between 0 and approximately 4,000,000,000. A maxlinks of 0 means there is no limit on the number of connections using the class.

<connect freq> applies only to servers, and specifies the frequency that the server tries to auto connect. Setting this to 0 will cause the server to attempt to connect repeatedly with no delay until the <maximum links> condition is satisfied. This is a Bad Thing(tm). Time can be specified as a number, or by giving something like: 1 minutes 2 seconds, or 1*60+20.

For connection classes intended for operator use, you can specify privileges used when the Operator {} block (see below) names this class. The local (aka globally_opered) privilege MUST be defined by either the Class or Operator block. It is highly recommended privileges be specified in the operator's Operator {} block, instead of in Class {} blocks.

Example blocks:

Uplinks you are not a hub for: <source lang="perl">Class {

 name = "Server"
 pingfreq = 1 minutes 30 seconds;
 connectfreq = 5 minutes;
 maxlinks = 1;
 sendq = 9000000;

};</source> Leaf servers you hub for: <source lang="perl">Class {

 name = "Leaf Server"
 pingfreq = 1 minutes 30 seconds;
 connectfreq = 5 minutes;
 maxlinks = 0;
 sendq = 9000000;

};</source> All clients: <source lang="perl">Class {

 name = "Users"
 pingfreq = 1 minutes 30 seconds;
 sendq = 60000;
 usermode = "+iw";

};</source> Opers: <source lang="perl">Class {

 name = "Opers"
 pingfreq = 1 minutes 30 seconds;
 sendq = 60000;
 whox = yes;

};</source>

Clients

Old I:lines

To allow clients to connect, they need authorization. This can be done based on hostmask, address mask and/or with a password. With intelligent use of classes and the maxlinks field in the Client {} blocks, you can let in a specific domain, but get rid of all other domains in the same top level, this setting up some sort of "reverse Kill {} block."